If i mess up my ECU (for which i have not seen one single post that this has happened) then it will be my fault. I have a Ford Focus MK2 2.0 l petrol car. I tried for curiosity to write the odometer on my car, I was able to increase the km value, but not to decrease it from the “odometer write” menu. Than I tried to use the menu under IC programming, called “write odometer value in km” or so. As I wrote the former value from this menu, the decreasing also didn’t succeeded, but many problems came instead of. If you want to configure modules,many of the BT units will fail and refuse without OBD2 adapter to progarm them. thinking more clearly.... there are three elements inside the PCM as I said, 1) Engine Map, 2) Immobiliser info 3) the disabled cruise control software. The FoCCCus software is originally developed for the Focus MK3. The original developer of the FoCCCus software stopped developing the software any further about 3 Years ago.

I've read that this step takes other people closer to 5 minutes, once the setup is correct, so I'm trying to figure out where I went wrong. The type of ELM327 software will all depend on the make and model of your vehicle. The ELM327 microchip is primarily designed to work with modern vehicles that utilize the CAN OBD2 protocol (ISO 15765-4). However, the chip is also compatible with the following OBD2 protocols: These are the modules available to you in ELMConfig, most of them are pretty self explanatory. Not all modules will be fitted to all cars, for example, only the Kuga will have the AWD module. If your car doesn’t have a module, it doesn’t mean that it can’t be fitted and the functionality added to your car. There have been success stories of people adding cruise control to cars, and enabling it using ELMConfig. MS-CAN GEM Reverse Rear Wiper Initial Wipe (Enabled/Disabled) – If auto wipers enabled, and car is put into reverse, rear window wiper will wipe (if rain is detected) you need to first cut 6 wires about 3 amp will do approx 6 inches long , different colours would be better , if not then mark them individually (14 , 11 , 6 , 3 , Hcan , and Mcan.

Please FIRST move the unextracted folder to your Desktop, else below #2 step won't show "Install" option. This update will enable a system which tries to detect a deflating tyre. This system does not use sensors in the wheel, instead it uses the ABS wheel speed sensors to detect when a wheel is rotating at a different speed to the others when it shouldn’t be. A deflating wheel will have a smaller circumference, so will rotate faster than the other wheels. This may not work on all cars.

Having connected the ELM327 module to the PC USB port and car OBD port and launched Forscan, I switched the ignition on when prompted – on my keyless start model this meant pressing the power button without pressing the clutch Before I read that, I was going to suggest you set it in the button test beep mode, to see if your steering wheel buttons are communicating with the car. Note: when connecting if FORScan says “No ELM Found”, flip the toggle switch to the other position and restart the connection process.If the OHP ELMconfig USB device connects, this is the HS-CAN position.Mark the adapter accordingly. You cannot read and erase error codes with this software. This software is used for configuring many ECU parameters. Very powerful software but a limited number of supported vehicles.bug: incorrect work of sevice functions "Read/Change Fuel Injector Correction factors" for Kuga 1.5 TDCi StgVI 2017+ model year What i will attempt to do is a guide for the FF2 (russian program) which will allow you to plug in a ELM 327 interface code reader into your focus Mk2 / Mk2.5 and update various parts of your car. This update will automatically switch on the rear (and front if fitted) heated screen(s) when the engine is running and the temperature drops below 3°C. De-solder pin 6 from the OBD port (Make Sure you label this wire if you have not used colour cable)